Can I run 125kHz RF circuit on a breadboard?CharliePlexing on a breadboardCan a switching power supply be built on a breadboard?Transfering Circuit from Veroboard to BreadboardBreadboard Quality questionsSchematic to breadboard circuitPIC Breadboard Circuit QuestionInconsistent behavior from circuit on breadboardCan I program a Breadboard with a laptop?Circuit to BreadboardCan I use the oscillation frequency equation for this circuit?
Time travel short story where a man arrives in the late 19th century in a time machine and then sends the machine back into the past
Coordinate position not precise
when is out of tune ok?
Minimal reference content
Irreducibility of a simple polynomial
Why are on-board computers allowed to change controls without notifying the pilots?
Increase performance creating Mandelbrot set in python
Go Pregnant or Go Home
How do I define a right arrow with bar in LaTeX?
Is there an Impartial Brexit Deal comparison site?
Teaching indefinite integrals that require special-casing
Greatest common substring
Why did Kant, Hegel, and Adorno leave some words and phrases in the Greek alphabet?
What's a natural way to say that someone works somewhere (for a job)?
Mapping a list into a phase plot
Curses work by shouting - How to avoid collateral damage?
Do I need a multiple entry visa for a trip UK -> Sweden -> UK?
Cynical novel that describes an America ruled by the media, arms manufacturers, and ethnic figureheads
Was the picture area of a CRT a parallelogram (instead of a true rectangle)?
Your magic is very sketchy
Is a roofing delivery truck likely to crack my driveway slab?
Is it correct to write "is not focus on"?
What will be the benefits of Brexit?
Is the destination of a commercial flight important for the pilot?
Can I run 125kHz RF circuit on a breadboard?
CharliePlexing on a breadboardCan a switching power supply be built on a breadboard?Transfering Circuit from Veroboard to BreadboardBreadboard Quality questionsSchematic to breadboard circuitPIC Breadboard Circuit QuestionInconsistent behavior from circuit on breadboardCan I program a Breadboard with a laptop?Circuit to BreadboardCan I use the oscillation frequency equation for this circuit?
6
$begingroup$
I was wondering if making a low frequency RF circuit on a breadboard is viable.
rf breadboard
edited Mar 21 at 0:20
JYelton
16.4k2891193
asked Mar 20 at 16:19
beginnerbeginner
394
New contributor
beginner is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
add a comment |
6
$begingroup$
I was wondering if making a low frequency RF circuit on a breadboard is viable.
rf breadboard
edited Mar 21 at 0:20
JYelton
16.4k2891193
asked Mar 20 at 16:19
beginnerbeginner
394
New contributor
beginner is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
1
$begingroup$
In a laboratory exercise i once built an 100MHz sine wave oscillator on a breadboard. We even added a mini jack to it and modulated it with music playing it on a handheld radio. It worked like a charm. I don't see any problem in 125kHz, just make sure to take care of the wiring.
$endgroup$
– Linkyyy
Mar 20 at 17:19
1
$begingroup$
By breadboard, do you mean a solderless breadboard? Or soldered protoboard?
$endgroup$
– Toor
Mar 20 at 18:13
4
$begingroup$
Should be ok. Here at my university, we have the second year students build a 5 stage 100KHz broadband opamp amplifier with 100dB gain on a breadboard! A bit mean for a lab, but many have it working. You do need to be careful with your layout though.
$endgroup$
– Adil Malik
Mar 21 at 1:25
1
$begingroup$
@Linkyyy Since you want to give OP an answer you should do it in the answer section.
$endgroup$
– pipe
Mar 21 at 8:42
$begingroup$
@AdilMalik Same comment to you as to Linkyyy and everyone else who wants to avoid the policy: You're trying to answer the question in a comment. Why? You have enough reputation to understand why this is bad, and you must have seen the explicit message to avoid it hundreds of times by now. You bypass the quality vetting that the whole Stack Exchange was designed to do and you push your 2 cents opinion before everyone who took the time to write a real and helpful answer.
$endgroup$
– pipe
Mar 21 at 8:47
add a comment |
6
6
6
2
$begingroup$
I was wondering if making a low frequency RF circuit on a breadboard is viable.
rf breadboard
edited Mar 21 at 0:20
JYelton
16.4k2891193
asked Mar 20 at 16:19
beginnerbeginner
394
New contributor
beginner is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
I was wondering if making a low frequency RF circuit on a breadboard is viable.
rf breadboard
rf breadboard
edited Mar 21 at 0:20
JYelton
16.4k2891193
asked Mar 20 at 16:19
beginnerbeginner
394
New contributor
beginner is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited Mar 21 at 0:20
JYelton
16.4k2891193
asked Mar 20 at 16:19
beginnerbeginner
394
New contributor
beginner is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited Mar 21 at 0:20
JYelton
16.4k2891193
edited Mar 21 at 0:20
JYelton
16.4k2891193
edited Mar 21 at 0:20
JYelton
16.4k2891193
16.4k2891193
asked Mar 20 at 16:19
beginnerbeginner
394
New contributor
beginner is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked Mar 20 at 16:19
beginnerbeginner
394
asked Mar 20 at 16:19
beginnerbeginner
394
394
New contributor
beginner is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
beginner is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
beginner is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
1
$begingroup$
In a laboratory exercise i once built an 100MHz sine wave oscillator on a breadboard. We even added a mini jack to it and modulated it with music playing it on a handheld radio. It worked like a charm. I don't see any problem in 125kHz, just make sure to take care of the wiring.
$endgroup$
– Linkyyy
Mar 20 at 17:19
1
$begingroup$
By breadboard, do you mean a solderless breadboard? Or soldered protoboard?
$endgroup$
– Toor
Mar 20 at 18:13
4
$begingroup$
Should be ok. Here at my university, we have the second year students build a 5 stage 100KHz broadband opamp amplifier with 100dB gain on a breadboard! A bit mean for a lab, but many have it working. You do need to be careful with your layout though.
$endgroup$
– Adil Malik
Mar 21 at 1:25
1
$begingroup$
@Linkyyy Since you want to give OP an answer you should do it in the answer section.
$endgroup$
– pipe
Mar 21 at 8:42
$begingroup$
@AdilMalik Same comment to you as to Linkyyy and everyone else who wants to avoid the policy: You're trying to answer the question in a comment. Why? You have enough reputation to understand why this is bad, and you must have seen the explicit message to avoid it hundreds of times by now. You bypass the quality vetting that the whole Stack Exchange was designed to do and you push your 2 cents opinion before everyone who took the time to write a real and helpful answer.
$endgroup$
– pipe
Mar 21 at 8:47
add a comment |
1
$begingroup$
In a laboratory exercise i once built an 100MHz sine wave oscillator on a breadboard. We even added a mini jack to it and modulated it with music playing it on a handheld radio. It worked like a charm. I don't see any problem in 125kHz, just make sure to take care of the wiring.
$endgroup$
– Linkyyy
Mar 20 at 17:19
1
$begingroup$
By breadboard, do you mean a solderless breadboard? Or soldered protoboard?
$endgroup$
– Toor
Mar 20 at 18:13
4
$begingroup$
Should be ok. Here at my university, we have the second year students build a 5 stage 100KHz broadband opamp amplifier with 100dB gain on a breadboard! A bit mean for a lab, but many have it working. You do need to be careful with your layout though.
$endgroup$
– Adil Malik
Mar 21 at 1:25
1
$begingroup$
@Linkyyy Since you want to give OP an answer you should do it in the answer section.
$endgroup$
– pipe
Mar 21 at 8:42
$begingroup$
@AdilMalik Same comment to you as to Linkyyy and everyone else who wants to avoid the policy: You're trying to answer the question in a comment. Why? You have enough reputation to understand why this is bad, and you must have seen the explicit message to avoid it hundreds of times by now. You bypass the quality vetting that the whole Stack Exchange was designed to do and you push your 2 cents opinion before everyone who took the time to write a real and helpful answer.
$endgroup$
– pipe
Mar 21 at 8:47
1
1
$begingroup$
In a laboratory exercise i once built an 100MHz sine wave oscillator on a breadboard. We even added a mini jack to it and modulated it with music playing it on a handheld radio. It worked like a charm. I don't see any problem in 125kHz, just make sure to take care of the wiring.
$endgroup$
– Linkyyy
Mar 20 at 17:19
$begingroup$
In a laboratory exercise i once built an 100MHz sine wave oscillator on a breadboard. We even added a mini jack to it and modulated it with music playing it on a handheld radio. It worked like a charm. I don't see any problem in 125kHz, just make sure to take care of the wiring.
$endgroup$
– Linkyyy
Mar 20 at 17:19
1
1
$begingroup$
By breadboard, do you mean a solderless breadboard? Or soldered protoboard?
$endgroup$
– Toor
Mar 20 at 18:13
$begingroup$
By breadboard, do you mean a solderless breadboard? Or soldered protoboard?
$endgroup$
– Toor
Mar 20 at 18:13
4
4
$begingroup$
Should be ok. Here at my university, we have the second year students build a 5 stage 100KHz broadband opamp amplifier with 100dB gain on a breadboard! A bit mean for a lab, but many have it working. You do need to be careful with your layout though.
$endgroup$
– Adil Malik
Mar 21 at 1:25
$begingroup$
Should be ok. Here at my university, we have the second year students build a 5 stage 100KHz broadband opamp amplifier with 100dB gain on a breadboard! A bit mean for a lab, but many have it working. You do need to be careful with your layout though.
$endgroup$
– Adil Malik
Mar 21 at 1:25
1
1
$begingroup$
@Linkyyy Since you want to give OP an answer you should do it in the answer section.
$endgroup$
– pipe
Mar 21 at 8:42
$begingroup$
@Linkyyy Since you want to give OP an answer you should do it in the answer section.
$endgroup$
– pipe
Mar 21 at 8:42
$begingroup$
@AdilMalik Same comment to you as to Linkyyy and everyone else who wants to avoid the policy: You're trying to answer the question in a comment. Why? You have enough reputation to understand why this is bad, and you must have seen the explicit message to avoid it hundreds of times by now. You bypass the quality vetting that the whole Stack Exchange was designed to do and you push your 2 cents opinion before everyone who took the time to write a real and helpful answer.
$endgroup$
– pipe
Mar 21 at 8:47
$begingroup$
@AdilMalik Same comment to you as to Linkyyy and everyone else who wants to avoid the policy: You're trying to answer the question in a comment. Why? You have enough reputation to understand why this is bad, and you must have seen the explicit message to avoid it hundreds of times by now. You bypass the quality vetting that the whole Stack Exchange was designed to do and you push your 2 cents opinion before everyone who took the time to write a real and helpful answer.
$endgroup$
– pipe
Mar 21 at 8:47
add a comment |
4 Answers
4
active
oldest
votes
16
$begingroup$
In my experience, yes, but you may need to take a few things into account.
- Some breadboards are better than others. The maximum frequency I've seen operating cleanly and reliably on a breadboard is 2 MHz. I've also seen breadboards that couldn't handle 200 kHz.
- You need to consider the maximum frequency present on the breadboard, not the largest "fundamental" frequency. For instance, a square wave signal (such as a clock or the 555's output) have very large harmonics up to maybe 5 or 7 times their fundamental frequency. If the breadboard can't handle these, then the clock will become distorted (low-pass filtered); additionally, if those harmonics spread through the breadboard, they'll distort potentially all your signals.
- Bypass capacitors become important as the frequency increases. Put one cap everwhere a circuit connects to the supply or ground, and you may have to sprinkle them around wherever high-frequency harmonics appear.
answered Mar 20 at 16:53
MBazMBaz
42827
$endgroup$
3
$begingroup$
I bought a bunch of electrolytic and ceramic caps with a 0.1" lead distance to sprinkle on breadboards, especially useful to place between the rails.
$endgroup$
– pipe
Mar 20 at 17:06
7
$begingroup$
I've seen 2kHz circuits fail on breadboards. Of course, that was done by someone who was in the process of getting a clue that big loopy wires may not be the best thing in an analog circuit.
$endgroup$
– TimWescott
Mar 20 at 17:23
1
$begingroup$
@TimWescott That's an excellent point that I forgot to include. You need very neat wiring with short cables and leads if you want a high-frequency breadboard circuit to work.
$endgroup$
– MBaz
Mar 20 at 18:01
2
$begingroup$
@TimWescott I've been that someone when I first built a circuit at school. :)
$endgroup$
– Graham
Mar 20 at 20:44
1
$begingroup$
I once accidentally made a 50MHz oscillator with two transistors and some resistors only on a bread board. It kind of gives you an idea of how much stray reactance there is.
$endgroup$
– Alex Cannon
Mar 21 at 2:03
|
show 2 more comments
12
$begingroup$
If you are insanely attentive to layout, yes. That means:
- Bypass everything with as short of wires as you can,
- Lay your wires down flat on the board (which pretty much means you'll be doing a lot of bending and possibly custom-cutting of wires). Big loops will kill you for sure.
- Be willing to use twisted-pair, or even small coax to go from one "major" stage to the next (i.e., if you're putting multiple breadboards together, use transmission line).
- Position your components so that the sensitive connections are short.
- And, of course, everything that I left out.
answered Mar 20 at 17:22
TimWescottTimWescott
6,4231416
$endgroup$
$begingroup$
Note that there are sets of pre-cut and pre-isolated wires with different breadboard-friendly lengths.
$endgroup$
– Jonas Schäfer
Mar 20 at 19:30
3
$begingroup$
@JonasSchäfer true. I've always felt it's more convenient to get a few rolls of 24-gauge solid wire and cut and strip as needed, rather than digging around in a box. But -- to each their own.
$endgroup$
– TimWescott
Mar 20 at 19:40
1
$begingroup$
Not meaning to criticize – I found this info useful for the OP. There are also sets with colour-coded and separated wire-lengths so that it’s not so much digging as grabbing exactly what you need. If you’re comfortable with cutting and stripping wire (I always get the length wrong), that’s probably overkill though :)
$endgroup$
– Jonas Schäfer
Mar 20 at 19:50
$begingroup$
@JonasSchäfer I wasn't meaning to criticize, either -- just pointing out that there's an alternative. I tend do do things slightly different than other people's preferences, so I'm not about to be the first one to step up and say that it's wrong to be different.
$endgroup$
– TimWescott
Mar 20 at 20:02
3
$begingroup$
You know that this is 125KHz, not 125MHz right? Of course if it's a 125KHz square wave it's really much higher than it would be as a sine wave so the edges could be rounded a little bit.
$endgroup$
– Alex Cannon
Mar 21 at 3:24
|
show 1 more comment
-2
$begingroup$
Yes, it's POSSIBLE but is never going to be as stable as a PCB.
Best you can do is avoid wires crossing, keep them as short as possible, and ensure your connections are good.
answered Mar 21 at 11:48
GigaJoulesGigaJoules
39112
$endgroup$
add a comment |
-2
$begingroup$
Actually, in the early days of radio when RF was below 500,000 CPS *** , most gear was built on a wooden breadboard with no concern for stray coupling. And it worked (sometimes). Good luck with your Branley coherer and watch out for the wouff hong.
*** CPS is a unit of frequency named for Charles Proteus Steinmetz.
answered Mar 23 at 15:05
richard1941richard1941
33715
$endgroup$
2
$begingroup$
A wooden breadboard is completely different in every respect that matters - this is an anecdote not an answer
$endgroup$
– Chris Stratton
Mar 23 at 16:16
add a comment |
Your Answer
StackExchange.ifUsing("editor", function ()
return StackExchange.using("mathjaxEditing", function ()
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
);
);
, "mathjax-editing");
StackExchange.ifUsing("editor", function ()
return StackExchange.using("schematics", function ()
StackExchange.schematics.init();
);
, "cicuitlab");
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "135"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
beginner is a new contributor. Be nice, and check out our Code of Conduct.
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f428185%2fcan-i-run-125khz-rf-circuit-on-a-breadboard%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
4 Answers
4
active
oldest
votes
4 Answers
4
active
oldest
votes
active
oldest
votes
active
oldest
votes
16
$begingroup$
In my experience, yes, but you may need to take a few things into account.
- Some breadboards are better than others. The maximum frequency I've seen operating cleanly and reliably on a breadboard is 2 MHz. I've also seen breadboards that couldn't handle 200 kHz.
- You need to consider the maximum frequency present on the breadboard, not the largest "fundamental" frequency. For instance, a square wave signal (such as a clock or the 555's output) have very large harmonics up to maybe 5 or 7 times their fundamental frequency. If the breadboard can't handle these, then the clock will become distorted (low-pass filtered); additionally, if those harmonics spread through the breadboard, they'll distort potentially all your signals.
- Bypass capacitors become important as the frequency increases. Put one cap everwhere a circuit connects to the supply or ground, and you may have to sprinkle them around wherever high-frequency harmonics appear.
answered Mar 20 at 16:53
MBazMBaz
42827
$endgroup$
3
$begingroup$
I bought a bunch of electrolytic and ceramic caps with a 0.1" lead distance to sprinkle on breadboards, especially useful to place between the rails.
$endgroup$
– pipe
Mar 20 at 17:06
7
$begingroup$
I've seen 2kHz circuits fail on breadboards. Of course, that was done by someone who was in the process of getting a clue that big loopy wires may not be the best thing in an analog circuit.
$endgroup$
– TimWescott
Mar 20 at 17:23
1
$begingroup$
@TimWescott That's an excellent point that I forgot to include. You need very neat wiring with short cables and leads if you want a high-frequency breadboard circuit to work.
$endgroup$
– MBaz
Mar 20 at 18:01
2
$begingroup$
@TimWescott I've been that someone when I first built a circuit at school. :)
$endgroup$
– Graham
Mar 20 at 20:44
1
$begingroup$
I once accidentally made a 50MHz oscillator with two transistors and some resistors only on a bread board. It kind of gives you an idea of how much stray reactance there is.
$endgroup$
– Alex Cannon
Mar 21 at 2:03
|
show 2 more comments
16
$begingroup$
In my experience, yes, but you may need to take a few things into account.
- Some breadboards are better than others. The maximum frequency I've seen operating cleanly and reliably on a breadboard is 2 MHz. I've also seen breadboards that couldn't handle 200 kHz.
- You need to consider the maximum frequency present on the breadboard, not the largest "fundamental" frequency. For instance, a square wave signal (such as a clock or the 555's output) have very large harmonics up to maybe 5 or 7 times their fundamental frequency. If the breadboard can't handle these, then the clock will become distorted (low-pass filtered); additionally, if those harmonics spread through the breadboard, they'll distort potentially all your signals.
- Bypass capacitors become important as the frequency increases. Put one cap everwhere a circuit connects to the supply or ground, and you may have to sprinkle them around wherever high-frequency harmonics appear.
answered Mar 20 at 16:53
MBazMBaz
42827
$endgroup$
3
$begingroup$
I bought a bunch of electrolytic and ceramic caps with a 0.1" lead distance to sprinkle on breadboards, especially useful to place between the rails.
$endgroup$
– pipe
Mar 20 at 17:06
7
$begingroup$
I've seen 2kHz circuits fail on breadboards. Of course, that was done by someone who was in the process of getting a clue that big loopy wires may not be the best thing in an analog circuit.
$endgroup$
– TimWescott
Mar 20 at 17:23
1
$begingroup$
@TimWescott That's an excellent point that I forgot to include. You need very neat wiring with short cables and leads if you want a high-frequency breadboard circuit to work.
$endgroup$
– MBaz
Mar 20 at 18:01
2
$begingroup$
@TimWescott I've been that someone when I first built a circuit at school. :)
$endgroup$
– Graham
Mar 20 at 20:44
1
$begingroup$
I once accidentally made a 50MHz oscillator with two transistors and some resistors only on a bread board. It kind of gives you an idea of how much stray reactance there is.
$endgroup$
– Alex Cannon
Mar 21 at 2:03
|
show 2 more comments
16
16
16
$begingroup$
In my experience, yes, but you may need to take a few things into account.
- Some breadboards are better than others. The maximum frequency I've seen operating cleanly and reliably on a breadboard is 2 MHz. I've also seen breadboards that couldn't handle 200 kHz.
- You need to consider the maximum frequency present on the breadboard, not the largest "fundamental" frequency. For instance, a square wave signal (such as a clock or the 555's output) have very large harmonics up to maybe 5 or 7 times their fundamental frequency. If the breadboard can't handle these, then the clock will become distorted (low-pass filtered); additionally, if those harmonics spread through the breadboard, they'll distort potentially all your signals.
- Bypass capacitors become important as the frequency increases. Put one cap everwhere a circuit connects to the supply or ground, and you may have to sprinkle them around wherever high-frequency harmonics appear.
answered Mar 20 at 16:53
MBazMBaz
42827
$endgroup$
In my experience, yes, but you may need to take a few things into account.
- Some breadboards are better than others. The maximum frequency I've seen operating cleanly and reliably on a breadboard is 2 MHz. I've also seen breadboards that couldn't handle 200 kHz.
- You need to consider the maximum frequency present on the breadboard, not the largest "fundamental" frequency. For instance, a square wave signal (such as a clock or the 555's output) have very large harmonics up to maybe 5 or 7 times their fundamental frequency. If the breadboard can't handle these, then the clock will become distorted (low-pass filtered); additionally, if those harmonics spread through the breadboard, they'll distort potentially all your signals.
- Bypass capacitors become important as the frequency increases. Put one cap everwhere a circuit connects to the supply or ground, and you may have to sprinkle them around wherever high-frequency harmonics appear.
answered Mar 20 at 16:53
MBazMBaz
42827
answered Mar 20 at 16:53
MBazMBaz
42827
answered Mar 20 at 16:53
MBazMBaz
42827
answered Mar 20 at 16:53
MBazMBaz
42827
42827
3
$begingroup$
I bought a bunch of electrolytic and ceramic caps with a 0.1" lead distance to sprinkle on breadboards, especially useful to place between the rails.
$endgroup$
– pipe
Mar 20 at 17:06
7
$begingroup$
I've seen 2kHz circuits fail on breadboards. Of course, that was done by someone who was in the process of getting a clue that big loopy wires may not be the best thing in an analog circuit.
$endgroup$
– TimWescott
Mar 20 at 17:23
1
$begingroup$
@TimWescott That's an excellent point that I forgot to include. You need very neat wiring with short cables and leads if you want a high-frequency breadboard circuit to work.
$endgroup$
– MBaz
Mar 20 at 18:01
2
$begingroup$
@TimWescott I've been that someone when I first built a circuit at school. :)
$endgroup$
– Graham
Mar 20 at 20:44
1
$begingroup$
I once accidentally made a 50MHz oscillator with two transistors and some resistors only on a bread board. It kind of gives you an idea of how much stray reactance there is.
$endgroup$
– Alex Cannon
Mar 21 at 2:03
|
show 2 more comments
3
$begingroup$
I bought a bunch of electrolytic and ceramic caps with a 0.1" lead distance to sprinkle on breadboards, especially useful to place between the rails.
$endgroup$
– pipe
Mar 20 at 17:06
7
$begingroup$
I've seen 2kHz circuits fail on breadboards. Of course, that was done by someone who was in the process of getting a clue that big loopy wires may not be the best thing in an analog circuit.
$endgroup$
– TimWescott
Mar 20 at 17:23
1
$begingroup$
@TimWescott That's an excellent point that I forgot to include. You need very neat wiring with short cables and leads if you want a high-frequency breadboard circuit to work.
$endgroup$
– MBaz
Mar 20 at 18:01
2
$begingroup$
@TimWescott I've been that someone when I first built a circuit at school. :)
$endgroup$
– Graham
Mar 20 at 20:44
1
$begingroup$
I once accidentally made a 50MHz oscillator with two transistors and some resistors only on a bread board. It kind of gives you an idea of how much stray reactance there is.
$endgroup$
– Alex Cannon
Mar 21 at 2:03
3
3
$begingroup$
I bought a bunch of electrolytic and ceramic caps with a 0.1" lead distance to sprinkle on breadboards, especially useful to place between the rails.
$endgroup$
– pipe
Mar 20 at 17:06
$begingroup$
I bought a bunch of electrolytic and ceramic caps with a 0.1" lead distance to sprinkle on breadboards, especially useful to place between the rails.
$endgroup$
– pipe
Mar 20 at 17:06
7
7
$begingroup$
I've seen 2kHz circuits fail on breadboards. Of course, that was done by someone who was in the process of getting a clue that big loopy wires may not be the best thing in an analog circuit.
$endgroup$
– TimWescott
Mar 20 at 17:23
$begingroup$
I've seen 2kHz circuits fail on breadboards. Of course, that was done by someone who was in the process of getting a clue that big loopy wires may not be the best thing in an analog circuit.
$endgroup$
– TimWescott
Mar 20 at 17:23
1
1
$begingroup$
@TimWescott That's an excellent point that I forgot to include. You need very neat wiring with short cables and leads if you want a high-frequency breadboard circuit to work.
$endgroup$
– MBaz
Mar 20 at 18:01
$begingroup$
@TimWescott That's an excellent point that I forgot to include. You need very neat wiring with short cables and leads if you want a high-frequency breadboard circuit to work.
$endgroup$
– MBaz
Mar 20 at 18:01
2
2
$begingroup$
@TimWescott I've been that someone when I first built a circuit at school. :)
$endgroup$
– Graham
Mar 20 at 20:44
$begingroup$
@TimWescott I've been that someone when I first built a circuit at school. :)
$endgroup$
– Graham
Mar 20 at 20:44
1
1
$begingroup$
I once accidentally made a 50MHz oscillator with two transistors and some resistors only on a bread board. It kind of gives you an idea of how much stray reactance there is.
$endgroup$
– Alex Cannon
Mar 21 at 2:03
$begingroup$
I once accidentally made a 50MHz oscillator with two transistors and some resistors only on a bread board. It kind of gives you an idea of how much stray reactance there is.
$endgroup$
– Alex Cannon
Mar 21 at 2:03
|
show 2 more comments
12
$begingroup$
If you are insanely attentive to layout, yes. That means:
- Bypass everything with as short of wires as you can,
- Lay your wires down flat on the board (which pretty much means you'll be doing a lot of bending and possibly custom-cutting of wires). Big loops will kill you for sure.
- Be willing to use twisted-pair, or even small coax to go from one "major" stage to the next (i.e., if you're putting multiple breadboards together, use transmission line).
- Position your components so that the sensitive connections are short.
- And, of course, everything that I left out.
answered Mar 20 at 17:22
TimWescottTimWescott
6,4231416
$endgroup$
$begingroup$
Note that there are sets of pre-cut and pre-isolated wires with different breadboard-friendly lengths.
$endgroup$
– Jonas Schäfer
Mar 20 at 19:30
3
$begingroup$
@JonasSchäfer true. I've always felt it's more convenient to get a few rolls of 24-gauge solid wire and cut and strip as needed, rather than digging around in a box. But -- to each their own.
$endgroup$
– TimWescott
Mar 20 at 19:40
1
$begingroup$
Not meaning to criticize – I found this info useful for the OP. There are also sets with colour-coded and separated wire-lengths so that it’s not so much digging as grabbing exactly what you need. If you’re comfortable with cutting and stripping wire (I always get the length wrong), that’s probably overkill though :)
$endgroup$
– Jonas Schäfer
Mar 20 at 19:50
$begingroup$
@JonasSchäfer I wasn't meaning to criticize, either -- just pointing out that there's an alternative. I tend do do things slightly different than other people's preferences, so I'm not about to be the first one to step up and say that it's wrong to be different.
$endgroup$
– TimWescott
Mar 20 at 20:02
3
$begingroup$
You know that this is 125KHz, not 125MHz right? Of course if it's a 125KHz square wave it's really much higher than it would be as a sine wave so the edges could be rounded a little bit.
$endgroup$
– Alex Cannon
Mar 21 at 3:24
|
show 1 more comment
12
$begingroup$
If you are insanely attentive to layout, yes. That means:
- Bypass everything with as short of wires as you can,
- Lay your wires down flat on the board (which pretty much means you'll be doing a lot of bending and possibly custom-cutting of wires). Big loops will kill you for sure.
- Be willing to use twisted-pair, or even small coax to go from one "major" stage to the next (i.e., if you're putting multiple breadboards together, use transmission line).
- Position your components so that the sensitive connections are short.
- And, of course, everything that I left out.
answered Mar 20 at 17:22
TimWescottTimWescott
6,4231416
$endgroup$
$begingroup$
Note that there are sets of pre-cut and pre-isolated wires with different breadboard-friendly lengths.
$endgroup$
– Jonas Schäfer
Mar 20 at 19:30
3
$begingroup$
@JonasSchäfer true. I've always felt it's more convenient to get a few rolls of 24-gauge solid wire and cut and strip as needed, rather than digging around in a box. But -- to each their own.
$endgroup$
– TimWescott
Mar 20 at 19:40
1
$begingroup$
Not meaning to criticize – I found this info useful for the OP. There are also sets with colour-coded and separated wire-lengths so that it’s not so much digging as grabbing exactly what you need. If you’re comfortable with cutting and stripping wire (I always get the length wrong), that’s probably overkill though :)
$endgroup$
– Jonas Schäfer
Mar 20 at 19:50
$begingroup$
@JonasSchäfer I wasn't meaning to criticize, either -- just pointing out that there's an alternative. I tend do do things slightly different than other people's preferences, so I'm not about to be the first one to step up and say that it's wrong to be different.
$endgroup$
– TimWescott
Mar 20 at 20:02
3
$begingroup$
You know that this is 125KHz, not 125MHz right? Of course if it's a 125KHz square wave it's really much higher than it would be as a sine wave so the edges could be rounded a little bit.
$endgroup$
– Alex Cannon
Mar 21 at 3:24
|
show 1 more comment
12
12
12
$begingroup$
If you are insanely attentive to layout, yes. That means:
- Bypass everything with as short of wires as you can,
- Lay your wires down flat on the board (which pretty much means you'll be doing a lot of bending and possibly custom-cutting of wires). Big loops will kill you for sure.
- Be willing to use twisted-pair, or even small coax to go from one "major" stage to the next (i.e., if you're putting multiple breadboards together, use transmission line).
- Position your components so that the sensitive connections are short.
- And, of course, everything that I left out.
answered Mar 20 at 17:22
TimWescottTimWescott
6,4231416
$endgroup$
If you are insanely attentive to layout, yes. That means:
- Bypass everything with as short of wires as you can,
- Lay your wires down flat on the board (which pretty much means you'll be doing a lot of bending and possibly custom-cutting of wires). Big loops will kill you for sure.
- Be willing to use twisted-pair, or even small coax to go from one "major" stage to the next (i.e., if you're putting multiple breadboards together, use transmission line).
- Position your components so that the sensitive connections are short.
- And, of course, everything that I left out.
answered Mar 20 at 17:22
TimWescottTimWescott
6,4231416
answered Mar 20 at 17:22
TimWescottTimWescott
6,4231416
answered Mar 20 at 17:22
TimWescottTimWescott
6,4231416
answered Mar 20 at 17:22
TimWescottTimWescott
6,4231416
6,4231416
$begingroup$
Note that there are sets of pre-cut and pre-isolated wires with different breadboard-friendly lengths.
$endgroup$
– Jonas Schäfer
Mar 20 at 19:30
3
$begingroup$
@JonasSchäfer true. I've always felt it's more convenient to get a few rolls of 24-gauge solid wire and cut and strip as needed, rather than digging around in a box. But -- to each their own.
$endgroup$
– TimWescott
Mar 20 at 19:40
1
$begingroup$
Not meaning to criticize – I found this info useful for the OP. There are also sets with colour-coded and separated wire-lengths so that it’s not so much digging as grabbing exactly what you need. If you’re comfortable with cutting and stripping wire (I always get the length wrong), that’s probably overkill though :)
$endgroup$
– Jonas Schäfer
Mar 20 at 19:50
$begingroup$
@JonasSchäfer I wasn't meaning to criticize, either -- just pointing out that there's an alternative. I tend do do things slightly different than other people's preferences, so I'm not about to be the first one to step up and say that it's wrong to be different.
$endgroup$
– TimWescott
Mar 20 at 20:02
3
$begingroup$
You know that this is 125KHz, not 125MHz right? Of course if it's a 125KHz square wave it's really much higher than it would be as a sine wave so the edges could be rounded a little bit.
$endgroup$
– Alex Cannon
Mar 21 at 3:24
|
show 1 more comment
$begingroup$
Note that there are sets of pre-cut and pre-isolated wires with different breadboard-friendly lengths.
$endgroup$
– Jonas Schäfer
Mar 20 at 19:30
3
$begingroup$
@JonasSchäfer true. I've always felt it's more convenient to get a few rolls of 24-gauge solid wire and cut and strip as needed, rather than digging around in a box. But -- to each their own.
$endgroup$
– TimWescott
Mar 20 at 19:40
1
$begingroup$
Not meaning to criticize – I found this info useful for the OP. There are also sets with colour-coded and separated wire-lengths so that it’s not so much digging as grabbing exactly what you need. If you’re comfortable with cutting and stripping wire (I always get the length wrong), that’s probably overkill though :)
$endgroup$
– Jonas Schäfer
Mar 20 at 19:50
$begingroup$
@JonasSchäfer I wasn't meaning to criticize, either -- just pointing out that there's an alternative. I tend do do things slightly different than other people's preferences, so I'm not about to be the first one to step up and say that it's wrong to be different.
$endgroup$
– TimWescott
Mar 20 at 20:02
3
$begingroup$
You know that this is 125KHz, not 125MHz right? Of course if it's a 125KHz square wave it's really much higher than it would be as a sine wave so the edges could be rounded a little bit.
$endgroup$
– Alex Cannon
Mar 21 at 3:24
$begingroup$
Note that there are sets of pre-cut and pre-isolated wires with different breadboard-friendly lengths.
$endgroup$
– Jonas Schäfer
Mar 20 at 19:30
$begingroup$
Note that there are sets of pre-cut and pre-isolated wires with different breadboard-friendly lengths.
$endgroup$
– Jonas Schäfer
Mar 20 at 19:30
3
3
$begingroup$
@JonasSchäfer true. I've always felt it's more convenient to get a few rolls of 24-gauge solid wire and cut and strip as needed, rather than digging around in a box. But -- to each their own.
$endgroup$
– TimWescott
Mar 20 at 19:40
$begingroup$
@JonasSchäfer true. I've always felt it's more convenient to get a few rolls of 24-gauge solid wire and cut and strip as needed, rather than digging around in a box. But -- to each their own.
$endgroup$
– TimWescott
Mar 20 at 19:40
1
1
$begingroup$
Not meaning to criticize – I found this info useful for the OP. There are also sets with colour-coded and separated wire-lengths so that it’s not so much digging as grabbing exactly what you need. If you’re comfortable with cutting and stripping wire (I always get the length wrong), that’s probably overkill though :)
$endgroup$
– Jonas Schäfer
Mar 20 at 19:50
$begingroup$
Not meaning to criticize – I found this info useful for the OP. There are also sets with colour-coded and separated wire-lengths so that it’s not so much digging as grabbing exactly what you need. If you’re comfortable with cutting and stripping wire (I always get the length wrong), that’s probably overkill though :)
$endgroup$
– Jonas Schäfer
Mar 20 at 19:50
$begingroup$
@JonasSchäfer I wasn't meaning to criticize, either -- just pointing out that there's an alternative. I tend do do things slightly different than other people's preferences, so I'm not about to be the first one to step up and say that it's wrong to be different.
$endgroup$
– TimWescott
Mar 20 at 20:02
$begingroup$
@JonasSchäfer I wasn't meaning to criticize, either -- just pointing out that there's an alternative. I tend do do things slightly different than other people's preferences, so I'm not about to be the first one to step up and say that it's wrong to be different.
$endgroup$
– TimWescott
Mar 20 at 20:02
3
3
$begingroup$
You know that this is 125KHz, not 125MHz right? Of course if it's a 125KHz square wave it's really much higher than it would be as a sine wave so the edges could be rounded a little bit.
$endgroup$
– Alex Cannon
Mar 21 at 3:24
$begingroup$
You know that this is 125KHz, not 125MHz right? Of course if it's a 125KHz square wave it's really much higher than it would be as a sine wave so the edges could be rounded a little bit.
$endgroup$
– Alex Cannon
Mar 21 at 3:24
|
show 1 more comment
-2
$begingroup$
Yes, it's POSSIBLE but is never going to be as stable as a PCB.
Best you can do is avoid wires crossing, keep them as short as possible, and ensure your connections are good.
answered Mar 21 at 11:48
GigaJoulesGigaJoules
39112
$endgroup$
add a comment |
-2
$begingroup$
Yes, it's POSSIBLE but is never going to be as stable as a PCB.
Best you can do is avoid wires crossing, keep them as short as possible, and ensure your connections are good.
answered Mar 21 at 11:48
GigaJoulesGigaJoules
39112
$endgroup$
add a comment |
-2
-2
-2
$begingroup$
Yes, it's POSSIBLE but is never going to be as stable as a PCB.
Best you can do is avoid wires crossing, keep them as short as possible, and ensure your connections are good.
answered Mar 21 at 11:48
GigaJoulesGigaJoules
39112
$endgroup$
Yes, it's POSSIBLE but is never going to be as stable as a PCB.
Best you can do is avoid wires crossing, keep them as short as possible, and ensure your connections are good.
answered Mar 21 at 11:48
GigaJoulesGigaJoules
39112
answered Mar 21 at 11:48
GigaJoulesGigaJoules
39112
answered Mar 21 at 11:48
GigaJoulesGigaJoules
39112
answered Mar 21 at 11:48
GigaJoulesGigaJoules
39112
39112
add a comment |
add a comment |
-2
$begingroup$
Actually, in the early days of radio when RF was below 500,000 CPS *** , most gear was built on a wooden breadboard with no concern for stray coupling. And it worked (sometimes). Good luck with your Branley coherer and watch out for the wouff hong.
*** CPS is a unit of frequency named for Charles Proteus Steinmetz.
answered Mar 23 at 15:05
richard1941richard1941
33715
$endgroup$
2
$begingroup$
A wooden breadboard is completely different in every respect that matters - this is an anecdote not an answer
$endgroup$
– Chris Stratton
Mar 23 at 16:16
add a comment |
-2
$begingroup$
Actually, in the early days of radio when RF was below 500,000 CPS *** , most gear was built on a wooden breadboard with no concern for stray coupling. And it worked (sometimes). Good luck with your Branley coherer and watch out for the wouff hong.
*** CPS is a unit of frequency named for Charles Proteus Steinmetz.
answered Mar 23 at 15:05
richard1941richard1941
33715
$endgroup$
2
$begingroup$
A wooden breadboard is completely different in every respect that matters - this is an anecdote not an answer
$endgroup$
– Chris Stratton
Mar 23 at 16:16
add a comment |
-2
-2
-2
$begingroup$
Actually, in the early days of radio when RF was below 500,000 CPS *** , most gear was built on a wooden breadboard with no concern for stray coupling. And it worked (sometimes). Good luck with your Branley coherer and watch out for the wouff hong.
*** CPS is a unit of frequency named for Charles Proteus Steinmetz.
answered Mar 23 at 15:05
richard1941richard1941
33715
$endgroup$
Actually, in the early days of radio when RF was below 500,000 CPS *** , most gear was built on a wooden breadboard with no concern for stray coupling. And it worked (sometimes). Good luck with your Branley coherer and watch out for the wouff hong.
*** CPS is a unit of frequency named for Charles Proteus Steinmetz.
answered Mar 23 at 15:05
richard1941richard1941
33715
answered Mar 23 at 15:05
richard1941richard1941
33715
answered Mar 23 at 15:05
richard1941richard1941
33715
answered Mar 23 at 15:05
richard1941richard1941
33715
33715
2
$begingroup$
A wooden breadboard is completely different in every respect that matters - this is an anecdote not an answer
$endgroup$
– Chris Stratton
Mar 23 at 16:16
add a comment |
2
$begingroup$
A wooden breadboard is completely different in every respect that matters - this is an anecdote not an answer
$endgroup$
– Chris Stratton
Mar 23 at 16:16
2
2
$begingroup$
A wooden breadboard is completely different in every respect that matters - this is an anecdote not an answer
$endgroup$
– Chris Stratton
Mar 23 at 16:16
$begingroup$
A wooden breadboard is completely different in every respect that matters - this is an anecdote not an answer
$endgroup$
– Chris Stratton
Mar 23 at 16:16
add a comment |
beginner is a new contributor. Be nice, and check out our Code of Conduct.
draft saved
draft discarded
beginner is a new contributor. Be nice, and check out our Code of Conduct.
beginner is a new contributor. Be nice, and check out our Code of Conduct.
beginner is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f428185%2fcan-i-run-125khz-rf-circuit-on-a-breadboard%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
1
$begingroup$
In a laboratory exercise i once built an 100MHz sine wave oscillator on a breadboard. We even added a mini jack to it and modulated it with music playing it on a handheld radio. It worked like a charm. I don't see any problem in 125kHz, just make sure to take care of the wiring.
$endgroup$
– Linkyyy
Mar 20 at 17:19
1
$begingroup$
By breadboard, do you mean a solderless breadboard? Or soldered protoboard?
$endgroup$
– Toor
Mar 20 at 18:13
4
$begingroup$
Should be ok. Here at my university, we have the second year students build a 5 stage 100KHz broadband opamp amplifier with 100dB gain on a breadboard! A bit mean for a lab, but many have it working. You do need to be careful with your layout though.
$endgroup$
– Adil Malik
Mar 21 at 1:25
1
$begingroup$
@Linkyyy Since you want to give OP an answer you should do it in the answer section.
$endgroup$
– pipe
Mar 21 at 8:42
$begingroup$
@AdilMalik Same comment to you as to Linkyyy and everyone else who wants to avoid the policy: You're trying to answer the question in a comment. Why? You have enough reputation to understand why this is bad, and you must have seen the explicit message to avoid it hundreds of times by now. You bypass the quality vetting that the whole Stack Exchange was designed to do and you push your 2 cents opinion before everyone who took the time to write a real and helpful answer.
$endgroup$
– pipe
Mar 21 at 8:47